BOB57 Cinematic LR & Freestyle 6inch HD System – iFlight

CHF 620.00CHF 650.00

Pre-Order now to get it first!
First batch around end of July 2022 in CH.

(1 customer review)

 

Thank you for support a small business!

Guaranteed Website with Safe Checkout

BOB57 Cinematic LR & Freestyle 6inch HD System – iFlight

 

 

The pilot & videographer Ellisvanjason and iFlight teamed up to craft a cinematic 6 inch drone that ensures agility and flight time and therefore combines the advantages of both 5 inch and 7 inch drones.

Features:

– 6 inch drone re-engineered: This drone was specifically designed for 6 inch

– H-shaped frame with robust middle section for less props in view while remaining stiffness

– XT60 front-mount: Compare to other drones the mount sits in the front and gives more space on the back.

– Built in BEC to directly power a gopro (no battery needed)

– Hybrid motor design: This motor is optimized for 6 inch.  Can be used with bi- blades (efficiency) and tri-blades (agility & trust). 

– Antenna mount: Solid antenna mount for less ocillations when using long antennas

– Long back bone: Enough space up to 3000mAh 6S batteries

– Gladiator shell: Protection shell from dust and water droplets (shall be removed for max. flight time)

– GPS: A high-end GPS is used to minimize the risk of failure during proximity flights 

– ESC: The drone consists iFlight’s new ESCs with built-in spike absober for more reliability

– Pre-Tune by Ellisvanjason

– 9min flight time with 1800mAh 6S

– 9+ with 3000mAh 6S Lipo or 4000mAh 6S Li-Ion

Specifications:

– Upper(middle) plate thickness: 2.5mm

– Bottom plate thickness: 1.5mm 

– Total Dimensions: 254*254mm 

– Bottom to top distance: 22mm 

– Geometry: H-shaped frame

– Top plate thickness: 2mm 

– Ellisvanjason 2506 motors 

– Gemfan 6032 propellers

– Arm Thickness: 6mm

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC)

FC //BLITZ F722 Flight Controller

  • Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
  • Smartaudio / IRC Tramp VTX protocol supported
  • Firmware target: IFLIGHT_BLITZ_F722
  • Motor outputs: 4x (SH1.0 connector)
  • Flash: 32MB (Blackbox flash)
  • I2C serial: SDA / SLA pads
  • Dimensions: 36.5*35 mm
  • Barometer: DPS310
  • OSD Chip: AT7456E
  • LED controller: Yes
  • MCU: STM32 F722
  • Beeper pad: Yes
  • Gyro: BMI270
  • Weight: 7.8g
  • UARTS: 6

 Product Link

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

  • Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
  • Mounting Holes: 30.5*30.5mm/Φ4mm
  • Target:   IFLIGHT_BLITZ_G2
  • Supports 2-6S Lipo input
  • Current sensor: Yes
  • Constant: 55 Amps 
  • Current rate: 200
  • Burst: 65 Amps
  • Weight: 15.3g
  • MCU: G071
  • BEC: No

 Product Link

BOB57 HD Included Components and Parts

  • 2 x GEMFAN 6032- CW propeller + 2 x  6032 CCW (Green)
  • 2 x GEMFAN 6032- CW propeller + 2 x  6032 CCW (Black)
  • 1 x Albatross LHCP 5.8GHz SMA FPV Antenna 150mm
  • 1 x Albatross LHCP 5.8GHz SMA FPV Antenna 60mm
  • 1 x USB Type-C 5V Balance Plug Power Cable 55mm
  • 2 x iFlight Lipo Strap 20*250mm (Black)
  • 1 x Nebula Pro Vista HD System
  • 1 x Pre-built and Tested BOB57

Note:

All iFlight BNFs are tested before shipment to guarantee the highest quality. 

If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.

iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com/support

Additional information

Receiver option: No selection

DJI / PNP, ELRS 2.4Ghz, TBS Crossfire NANO RX

Brand: No selection

iFlight

1 review for BOB57 Cinematic LR & Freestyle 6inch HD System – iFlight

There are no reviews yet.

Be the first to review “BOB57 Cinematic LR & Freestyle 6inch HD System – iFlight”

Your email address will not be published. Required fields are marked *